[ Pobierz całość w formacie PDF ]

has seeded the cell, but as yet, is not  breeding , that is, the orgone concentration is not yet great enough to
attract additional orgone flow to itself. With the right cell, water and operator, it is possible to go straight to
Stage 2 on the first turn on of a new cell.
Stage 3: Not many people get to this stage, or what is worse, get here incorrectly. If you get here following
the above steps, your water is still crystal clear with no deposits in the sump. If you get here by brute force,
you will have stripped appreciable amounts of material from the cylinders and this material will now be
deposited on the insulators and suspended in the water as tiny particles which never settle out, and finally,
the material will form a deposit at the bottom of the cell. The low resistance insulators and the metallic
particles in the water will create a cell which leaks orgone and consequently it will cause endless mysterious
car stoppages or refusals of the car to start.
Right, the miracle of Nature is now breeding in your cell. Upon turning your power on to the cell, within 30
seconds copious beautiful white bubbles will rise from all the surface area of the cell. Before these bubbles
cover the water surface, you will notice a slowly rotating and pulsing front in all cylinders, that is
synchronised and has a regular rhythm of about 2 pulses per second and a clockwise rotation speed of
about 1 revolution every 2 seconds. These effects are very hard to observe for a first time viewer who does
not know what to look for. I find it easier to watch these effects with the aid of a fluorescent light, as the 100
cycles per second pulsations of the light "strobe" the water surface and help the observation.
The bubbles may overflow the container and show great surface tension. One of the definite proofs that the
cell is breeding is that, on turning the power source off and coming back the next day, most of the bubbles
will still be on top of the water as opposed to Stage 1 or Stage 2 where they disappear in minutes. There is
no way that you can mistake this stage. The bubbles are larger and pure white, the surface tension is
greater, the bubbles are pulsating and most importantly the surface tension remains days after the power
has been removed.
I do not recommend any additional tests or measurements. But for those who are incapable of leaving
things be, they may measure the voltage across the cell after it has been left standing with the power off for
at least 24 hours. A Stage 3 cell will have a residual voltage, or more correctly, a self-generated voltage of
around 1 volt. A Stage 1 cell measured under similar conditions will read 0.1 to 0.2 volts. Remember, that
unless you know what you are doing, these voltage measurements can be very misleading due to probe
materials and battery effects that can easily mask your true measurement. As the cell reaches the maximum
density of orgone that it can hold, the result of the breeding process is the conversion of this excess orgone
into the formation of electricity. As such, electrical measurement with the correct instruments is a very
valuable method in the verification of the efficiency of the cell. If you are conversant with the work of William
Reich, you may care to make an orgone meter and thus remove all guesswork. This meter is fully described
on some web sites.
I do not recommend any form of bubble exploding. As noted earlier, noise and vibration are orgone-
negative. Therefore, these explosions applied during the delicate seeding period will kill your cell. Apart from
a dead cell, the chance of fire igniting other gasses in the workshop and injuries to the ears etc. makes this
exercise highly unnecessary. I must admit that I too fell for the "go on, ignite it!" feeling. I had a cell that had
been at Stage 3 for seven months. It was my favourite test cell. My hands and matches fought my brain and
they won. There was a huge "ear-pulling, implosion/explosion", and yes, I killed the cell. It went back to
Stage 2 for four days. I will not do it again.
As all water we are using so far has been electrolysed, this water is not suitable for use in non-stainless steel
or glass containers due to reaction with the container and the resultant corrosion, but if you have to, or want
to, you can use juvenile water with no electrolyte added and still charge it to Stage 3. As the ion count is
much lower, the water is not as conductive, i.e. you cannot get as much current flow with 12 Volts as you [ Pobierz całość w formacie PDF ]